Home | 로그인 | 회원가입 | 사이트맵






     
 
 
제품소개
DSP
PowerPC
ARM & Xscale
Pentium Processor
MIPS Core
I2C/SPI/USB/MDIO
Memory Tester
Test & Measurement
 
 
 
HOME > 제품소개
제품 [Emulator] JTAGjet-C2000

TMS320C2000 DSP Emulator Texas Instruments 의 C2000 계열 DSP 전용으로 개발된 이 장비는 C24xx계열 및 C28xx계열의 모든 Processor를 지원한다. C2000 프로세서의 디버깅 및 고속 Flash Programming이 가능한 이 장비는 가격이 저렴하고 USB 1.1/2.0모두 지원하며 별도의 외부 전원을 사용하지 않고 USB 전원으로 동작하기 때문에 사용하기가 편리하고, 시스템의 구성이 간단하다. Code Composer Studio 3.x 에 대한 Driver를 기본 제공하므로 기존 개발 환경의 변경없이 그대로 사용할 수 있으며, 멀티코어, 멀티 프로세서 디버깅 기능을 제공하기 때문에 하나의 타겟보드에 두개의 프로세서가 실장된 경우에도 하나의 장비에서 디버깅이 가능하다. 무엇보다 가격이 저렴하고 CCS와 독립적으로 운용될 수 있는 Flash Programming Utility를 제공하므로 특히 양산용으로 사용하기에 최적의 조건을 제공한다. 

TMS320C24xx / TMS320F28xx DSP Support
JTAGjet-C2000
supports the
following C2000
DSP devices:
TMS320C24x
TMS320C28xx
TMS320C280xx
TMS320C2833x
TMS320F24x
TMS320F28xx
TMS320LC240x
TMS320LF240x
TMS320R28xx

Hardware Features (DSP emulator)
     
Supports TI TMS320C24xx and F28xx DSPs.
USB 2.0 high-speed port (480 Mbps) provides faster downloads.
Programmable JTAG clock from 1KHz to 30 MHz.
Supports all on-chip breakpoints and RTDX
Powered by the USB port – no external power adapters needed.
3 LEDs provide status of target power, JTAG activity, PC host activity and emulator power.
Available opto-isolator JTAG adapter.
     

 

Compatible with Code Composer Studio (DSP emulator) JTAGjet-C2000 is fully compatible with Code Composer Studio 3.1 or newer. It installs directly into the Code Composer Studio directories and becomes visible as JTAGjet Emulator in the CCS Setup utility and preconfigured with many C2000 targets. Setting up to work with JTAGjet is just as easy as setting up a TI emulator – just drag and drop the preconfigured target and emulator configuration and start CCS.

JTAG Chain Device Detection For custom made boards with more than one device on the JTAG chain, JTAGjet can detect all devices on the chain which is necessary in to configure the CCS debugger.

 Software Features (DSP emulator)
     

Supports Code Composer Studio 3.1 (or newer).

Optional Flash Programmer utility (does not need CCS).
Change JTAG clock even when the CCS is running.
Detects and graphically shows all devices on the JTAG chain.
Graphically monitors all pins on the JTAG header.
Windows Vista, XP, 2000, NT, ME, 98 & 95 compatible.
 

Variable JTAG Clock JTAGjet-TMS supports variable JTAG clock. It defaults to 10 MHz, but may be set as low as 1 kHz (for slow FPGA prototypes or power saving devices) to 30 MHz to provide faster application downloads and quicker Flash programming.

 

Auto-Sensing JTAG voltage JTAGjet-TMS comes with a detachable, active JTAG probe to better accommodate long scan chains and various JTAG pinout standards and low voltages. The standard probe comes with 14-pin XDS510 & XDS560 compatible header and supports targets from 3V to 5V. A low voltage probe is available as option for targets between 1.4V and 4.5V.